VOLKSWAGEN LT MK1 (1976-1996) - Rear Bumper Storage System
VOLKSWAGEN LT MK1 (1976-1996) - Rear Bumper Storage System
Pivoting storage that allows full access to the rear of the vehicle
This is an incredibly versatile rear bumper replacement that allows storage boxes and spare wheels to be mounted on the rear bumper and hinges them out of the way to give full access to the rear of the vehicle.
The base kit includes:
- A fixed main bumper beam that bolts under the vehicle into the existing chassis rails.
- Pivoting left and right hand mounting beams with bolt hole patterns that allow flexible attachments of accessories. The beam pivots are fitted with long-life engineering grade pivot bushes for ease of movement.
- Locking latches for both mounting beams.
- Two recovery shackle lugs that are positioned to take recovery loads directly back to the main chassis rails.
- Side bumper extensions that replicate the original wrap-around bumper ends.
Onto this base kit you can add:
An Accessory Module: this bolts to either pivoting beam and provides a horizontal surface that can be used to mount a storage box or any other suitable accessory. If a wheel carrier is not fitted then two Accessory Modules can be installed.
A Wheel Carrier Module: this also bolts to either pivoting beam and can accept a wheel with 5 bolts on a 160mm diameter.
This kit is manufactured from stainless steel throughout and is supplied unpainted for you to finish as you wish.
Please note that our kit does not include any storage boxes, recovery shackles or wheels!
If you need a different accessory mount to fit some other kit to the bumper then let us know and we will see if we can add it to our standard range!
Verfügbarkeit für Abholungen konnte nicht geladen werden
MORE DETAILS
Vehicle Requirements
Vehicle Requirements
This kit will fit VOLKSWAGEN LT MK1 vans. 1976-1996.
Construction
Construction
This product very robust and is manufactured throughout from stainless steel. The main beams are 5mm thick, the recovery shackle lugs are 2x10mm thick and other non-structural components are 3mm thick.
The pivoting beams, when fully loaded, move easily with one hand and the pivot bearings require no lubrication or maintenance, other than the usual routine checks to make sure fasteners are tight.
When latched, the pivoting beams locate on ABS pads that can be adjusted to ensure that the beams are rigidly located and cannot move in transit.
Made in Yorkshire
Made in Yorkshire
This product is designed and manufactured in Yorkshire and uses Yorkshire grit and ingenuity to bring you a high quality product with really practical features.
Fitting Instructions
Fitting Instructions
Installation
Installation
It is important that you test fit and assemble this kit BEFORE painting or powder coating to ensure that everything fits correctly. We cannot accept product returns that have been painted first then found to not fit your vehicle.
Installation is straightforward and has the following key steps:
- Remove the existing rear bumper.
- Fit the main bumper beam by inserting the support rails into and under the main vehicle chassis rails and bolt in place.
- If the pivoting beams have not been fitted to the main beam, fit these by inserting the pivot pins into the main beam pivots and fit the clamp washer underneath to hold in place. Ensure that two 'top-hat' plastic bearings are used, one at the top and bottom of each pivot.
- Fit the locking latches.
- Fit and adjust the plastic beam packers behind the latches to ensure that the pivoting beams lock firmly in position without any lateral or vertical movement.
- Fit any Accessory or Wheel Carrier modules that you have purchased.
- Check that the beams pivot freely and that no components clash with the vehicle.
- Once you are satisfied that he unpainted kit fits and works correctly, remove it and fully dismantle for painting or powder-coating. IMPORTANT NOTE: Carefully remove the plastic bearing from both pivots before coating and ensure that when applying the coating that the pivot pins are masked from paint and that the inside bore of the pivots on the main beam are also masked.
- When coating is complete, reassemble the kit.
Lead Time
Lead Time
This product is made to order, typically on a 8 week lead time. Once you place your order we will schedule it into production and complete it as soon as possible.
